Drywall in Toronto

image-drywall-in-Toronto

Drywall installation in Toronto

Drywall in Toronto – important stages of installation and work with this material.

Many of us are sure that drywall is a modern building material, which came into use only at the end of the last century. No! In fact, such a material has been used for about 200 years. Of course, during this time production technologies have changed, but this does not cancel the following fact: everyone can master the basic aspects of handling drywall on their own. Drywall installation in Toronto!

Drywall in Toronto

As a rule, today nobody uses wooden bars for frame mounting anymore, instead of them metal.

Work with drywall in Toronto is done with 4 types of profiles.

  • Guiding profiles for frame creation, also often called UW. They have a standard depth of 40 mm and can be 50, 75 or 100 mm wide. The guide profiles are used to create the basis for the fastening of pole and ceiling profiles.
  • Ceiling rails – UD have the same function as the previous profiles, but are used for false ceilings.
  • Ceiling rails – CD and are used to create a framework and lintels. They are inserted into rails and fixed to the ceiling by hangers, crabs and anchor clamps.
  • CW ceiling profiles are used when it is necessary to install drywall partitions or to create walls. They are fastened into rails.

The main fixing elements for the frame profile are self-tapping screws, which are 9 to 12 mm long. There are also rivets and mounting pliers for connecting several profiles. The frame is fastened to the wall or ceiling by anchors or dowel nails.

Do not be afraid of the large set of parts used to drywall installation in Toronto. This is by no means a complete list of what professional builders use. In addition, do not forget that a one-time job involves only direct suspensions, CD and UD, dowel nails or anchors.

Special attention should be paid to tools for mounting drywall on walls.

Since you will have to drill holes in profiles, walls and other materials, buy or rent a hole punch with 3-5 Joules impact force. It is much easier to make a hole in concrete with the drill than with a impact drill. It just can’t handle that many holes. Also, the perforator is perfect for mixing different putty mixes and mounting. You need a special mixer attachment for this.

Equally important is a cordless screwdriver with a set of special nozzles to screw in screws with different types of flat bars.

In addition to power tools, hand tools are also used:

  • hammer;
  • metal scissors;
  • screwdriver;
  • office knife;
  • markers;
  • laser level or hydro level;
  • drywall planks;
  • pliers.

To attach to the wall one post of frame height of 2.5 m, use direct hangers in the amount of five pieces, ie every 50 cm – 1 hanger.

Two anchors are used for fastening each of them, 10 holes in total are to be drilled. The distance between the props is 60 cm, so for a wall 6 m long and 2.5 m high you will need 7 frame props and 70 holes.

How to work with drywall in Toronto

Working with drywall in Toronto. is primarily about creating a framework and its further cladding. Usually, structures made of drywall in Toronto are used to create lighting, aligning walls, building partitions, arches and niches.

Drywall installation in Toronto is as follows.

Step back at least 3 cm from the wall (profile width) and make the marks: use plumb line or laser level to draw a line on which the drywall will be placed.

Attach the UD main rails to the floor and ceiling. Their edge should follow your line.

After that, the vertical racks of the CD profiles should be set up. To do this, they are inserted into the rails and screwed to each other with screws.

To stiffen the CD profiles, they are attached to the wall every 50 cm using hangers that attach to the wall with two dowel nails. The hangers are screwed to the profiles with screws and their corners are bent.

The width of the standard drywall sheet is 120 cm, so the distance between the centres of the CD profiles is 60 cm.

After the frame is mounted, a heater, electrical wiring, water pipes or heating pipes are placed into the frame.

When installing drywall sheets on the ceiling, not only direct hangers are used, but also wire rods and “butterflies”, which have special steel “wings” that fix the rods at the right distance from the ceiling.

Types of fasteners to create a framework.

Installing drywall on the ceiling assumes that you use special fasteners – anchors.

Self-tapping screws for installing drywall in Toronto are screwed in 25-30 centimeters steps.

If you need to cut the sheet of drywall, it can be very easy to do with your own hands. To do this, cut the cardboard and a few millimeters of plasterboard with a stationery knife, and then break it at the corner of the table. Cut the second layer of paper after the breakage.

Read our blog!