If you have bought a granite paving stone and want to independently make paving of the chosen site, in this article the information on technology of paving granite will be collected.
1. Markings of a site for the subsequent paving by a paving granite stone
It is necessary to define the boundaries of the section, find out what objects will interfere (protrusions, bends, pipes, etc.). Further it is necessary to investigate a ground on which paving granite stone will be laid. To check up a ground on its uniformity if the ground is not uniform – to take measures on its consolidation go replacement of a part of a ground on more dense.
At designing of boards it is necessary to consider a slope of water, reference corners, points of installation of beacons.
2. Preparing the ground for paving
The quality of granite paving is always a carefully prepared foundation. If the foundation work is not done correctly – your granite stone, the paving stone will not last long. In a few years you will already see subsidence marks, flooded areas, cracked stones…
The first procedure in preparation of the base is removal of the top layer of soil, in its place layers of crushed stone and sand. Then fix these layers with dry mix. Each layer needs to be tampered with – manually or with equipment that can be rented.
Subsequent paving of paving stone is only possible after all layers have been evenly distributed and compacted.
3. Paving tracks with paving granite stones (paving slabs) on a concrete base
Here, the technology is simpler than working with unprepared soil. Almost here, we have a paving stone base ready for laying. It is used in areas where the pavement will be subjected to high loads. To begin with, a paving court is excavated, which is the same area as the paving area.
The depth is usually chosen within 30-40 cm. The area is evenly filled with 10-15 cm of crushed stone. Then the tramway is manually driven by a vibrating machine.
Then the formwork is made and fastened into which the concrete will be poured and fixed before it cures. After the concrete has dried up, we distribute a layer of dry mixture 3-5 cm thick across the concrete. Here we have the paving site ready for you.
4. Power of a paving granite stone on a dry mix
One more common method of laying paving granite stone is paving on dry mix. It is necessary to dig out the area of paving to a depth of 30 cm. Then it is filled with a layer of crushed stone in 10-15 cm and tamped with the available method.
Then the crushed stone is covered with a layer of 10 cm of sand and also tamped. When tamping sand can be used to water it – this allows the sand to more effectively fill the space in the crushed stone. Then the dry mixture of 4-6 cm is filled in. Such a foundation becomes the basis for the entire paving technology of the paving stone to become a much better .
5. Paving granite paving stone on the sand
Granite stone paving is often used for garden paths, paths in kindergartens, hospitals. This method is used where there will be no high load on the paving stone. For this purpose, the soil is removed from the selected area, at a depth of 20-25 cm.
A geotcan (flat water-permeable polymeric (synthetic or natural) textiles, nonwoven, woven or knitted, used in geotechnics or other building applications in contact with the ground and/or other building materials) is placed at the bottom of the excavated area to prevent the various plants from breaking through the cracks between the stone. Crushed stone is poured onto the surface of the fabric in a layer of approximately 10 cm. The crushed stone must be compacted in a quality manner.
Then a 10 cm layer of sand is poured in and compacted. As a result we have a ready platform for packing of a granite paving stone.
6. Setting up a curbstone
The final stage is the fixation of the curbstone. It is necessary that the territory where the granite paving stone was laid was fixed and did not allow to crawl or squeeze under the influence of the external ground. First of all it is necessary to dig out a trench which will pass along a path or already marked area. This trench must match the depth of the kerb installation.
Then we prepare a concrete mortar. The kerb stone should be installed in the concrete mix at half its height, the stones should be placed at the level, they should be installed and fixed with the concrete mortar that has not yet frozen. The kerb is fixed immediately after the concrete has hardened and this is only done on the outside of the paving operation.
If the preparation of the base and the kerb stone laying are not of good quality, what are the consequences?
Poor quality laying, over time, will cause the formation of puddles, deformation of the laid stone, irregularities, elevations or failures, reducing the life of granite products. If all is made correctly – water does not remain on a tile, after all everything is made under a small slope. There should not be any backlashes (differently plants or water will seep through slots) and even the knocked down drawing, absence of symmetry too concern poor quality packing.
The cottage is a great place to relax on a weekend or holiday. Building a veranda can become a dining room in the open air, and if it is heated, you can use the room all year round.
There are several varieties of verandas, and the simplest of them is considered an open structure. It consists of a canopy in front of the house entrance, a platform and a fence.
Closed verandas imply the construction of walls with partial glazing instead of a fence. The so-called French veranda is a building with all-glass walls, from floor to ceiling.
Pouring the foundation for the veranda
Work on the veranda will have to start with the casting of the foundation. His choice is determined by the same considerations as the construction of the main house:
- by the weight of the construction;
- the type of soil itself;
- the depth of soil freezing and the proximity of groundwater.
Most often a column base is arranged. It is the best choice for lightweight wood structures. If you are planning a closed veranda, and also with brick or block walls, it is better to stop at a strip foundation. It will cost more, but will facilitate further construction, and will last longer. It will be a floor support.
With movable soil for the veranda will have to make a pile base. It consists of steel rods hammered into the ground for several meters. The structure can withstand tens of tons of cargo (which is more than enough) and is also cheap in terms of material costs. However, it requires the rental of special equipment for its installation.
The procedure for performing work on the veranda foundation is as follows:
- Dig a trench around the perimeter of the building (for belt support) or a hole under the pillars. In both cases, a depth of 50 cm is sufficient.
- Crushed stone and sand layers will be poured on the bottom, each 10 cm thick and carefully tamped.
- The formwork will be installed, with the sides to be 20-25 cm high above the ground.
- The resulting cavities are poured with concrete.
Drainage channels are dug around the supports to drain water. The ground is removed 25 cm deep and about one meter wide, and the resulting cavities are filled with sand, expanded clay or fine crushed stone. From above, everything is covered with earth.
Construction of floor and veranda walls
Usually the aboveground part of the veranda is built of wood. It’s simple and fast, and it’s profitable. Working with wood does not require any special tools. Of the different types of wood, pine is the most suitable. It is cheap, but at the same time quite practical. Treatment with antiseptic will help protect it from fungus and harmful parasites.
The first thing you have to do is lay the floor. To maintain the stiffness of the flooring, the supports should be placed underneath each meter. The easiest solution is to place the columns with the required pitch right on the ground. So that the water does not stay on the floor later, you need to give the floor a slight slope from the house.
Please note! If a warm veranda is planned, the floor should be insulated. For this purpose, 50×50 or 50×80 mm thick beams with an offset of 50 cm should be fixed over the lower deck. Any suitable thermal insulator is fixed between them, and a clean floor is already laid on it.
Veranda wall construction options can vary greatly. In the simplest case, it is a light fence enclosing the veranda around the perimeter. In more complex variants low walls of wooden frame shields or even bricks are erected. Both are the basis for the installation of window frames. If the annex is supposed to be heated, it makes sense to put single-chamber double-glazed windows, and the walls below are additionally covered with insulation, such as foam plastic, and a decorative coating like siding.
An interesting type of closed structure is the French veranda. Its walls form solid metal-plastic double-glazed windows, sometimes bent in the form of a half arch. It is difficult to make such a structure with your own hands. It is better to order the manufacture and assembly at the appropriate firm. Installation will consist of installation at the corners of support poles and fixing the frame.
Construction of the veranda roof
Traditionally, two types of roofs are erected over summer extensions: either flat or pitched, with a slope angle of at least 25°. However, even a flat roof is desirable to give a small slope, about 5 °, so that rainfall does not stay on it.
Roofs for the veranda, as a rule, are supporting, that is, their supporting beams are supported by pillars made of brick or wood. On the other hand, they are fixed to the wall of the house with the attached bar of the same cross section, usually 50×50 mm.
Floor lags (for flat roofs) or rafters (for pitched roofs) are placed between the support beams.
The waterproofing is spread over the wooden “skeleton” and any suitable roofing material is fastened using purlins.
On the inside, the roof is also insulated and covered with a decorative coating. And the thermal insulation is most effective for pitched structure, and with flat roof insulation the reduction of heat loss is no more than 20-25%, regardless of the material.
Read our blog!
Just decided on the place of residence outside the city, the question arises – what to do with the plot of land. Well, if bought with a well-groomed lawn, if the area is not prepared? Or do not like the view near the built house? Usually a country house means a place for rest, leisure, and unattended plot spoils the mood. Built area allows you to fully enjoy the rest with friends, after a hard day’s work, to spend the holidays.
The company Captain Handy, which is engaged in landscape design in Ontario, landscaping in Toronto, landscape gardening in Toronto will help in the decision of territory improvement. Our team of professionals loves business which is engaged, thus considers wishes of clients. The company represents complex services, up to the subsequent service of the household plot at the request of the client.
The designer takes into account every detail, and an unusual and creative approach to the order helps to create a stunning style, uniqueness of landscape design. You can rely on the company – we have been successfully leading the market for many years, during this time we have successfully implemented hundreds of projects, helped many people.
We will help to change the site so that you can enjoy the view, feel only positive feelings sitting with your loved one on the terrace holding a cup of coffee or playing with children on the grass near the house. On the practical side, the designers will create a landscape in Ontario so that it is beautiful, functional. We provide our services not only in Toronto and the area, but also throughout Canada.
There’s no doubt about the landscaping of the farmhouse
As a rule, the difficulty of bringing the site in order arises in the independent planning of design. Each family member sees the final view of the area in its own way and it is difficult to translate the tastes of the family in one project. What to do if there is simply no time for planning and understanding the nuances of landscape design?
In order not to make a creative mess on the site, you just need to call a team of professionals. Landscape designers will help with the choice of plants, the location of arbours, plantings, clarification, correctly carry out automatic irrigation. The company Captain Handy provides a full range of landscape design services in Ontario:
- Landscape project from a specialist
- Arrangement of a rockery, a flower bed, alpine hills, Japanese gardens
- Design and subsequent construction of decks, pergolas, garden bridges
- Laying at your choice – natural, roll up lawn
- Creation of water reservoirs for every taste and every complexity
- Organization of both automatic and drip irrigation
- Installation of farmstead lighting and lane laying
- If necessary, we take care of the site at the end of work
- We’re strengthening the coast.
We, a team of specialists will help improve the site quickly, qualitatively, for a reasonable price with a real guarantee. In developing a project of the future landscape uses the latest technology – 3d and 2d modeling and visualization. For those who first used the services of the designer, and does not know how to properly monitor the site, we can create a landscape with minimal labor costs. Thus, the garden will enjoy the beauty at any time of year and time of day.
As a rule, after the completion of all construction work there is no strength and time to take care of the plot of land. Our company will help in the care of plants, maintaining cleanliness, fighting pests and beetles, fertilizing the site.
How to landscape design your site. The stages of our cooperation
Any dream must come true – there is no need to go abroad to see the exotic, you can do it in your yard. And if you like the classic style of landscape design in Toronto or mixed, in any case, we will help you decide on the choice.
Many people are vaguely aware of what landscape design is and whether it is needed at all. Also worried that it will be expensive, wishes will not be heard. All these are empty fears and lack of information about landscaping in Ontario.
When contacting Captain Handy, a specialist will tell you in detail what will be used, how the work will be carried out and which teams will work on your landscape. The consultation is free of charge, you just need to call to the office or write to e-mail. Have you stopped being afraid? Then we’ll discuss the stages of joint cooperation:
- Going to the site of your future work. Survey of the site, discussion of preliminary cost.
- We’ll be sure to sign a contract, get an advance to develop the project.
- Once the visual landscape project is ready, there is a discussion about your wishes. When everything is agreed and approved, the designer begins to transfer the visual design to the drawing.
- We further discuss, agree on the estimate and list of necessary materials for the work.
- Realization of the drawing on the nature under the supervision of the designer – excavation works, watering, lighting, lawn, paths, planting of plants.
- You accept the renovated site and we provide a one-year warranty on materials and work performed.
As can be seen from the points of the stage, we take our work responsibly, there is no criticism or bad feedback on our work. In this case, we are open to dialogue with the customer, prompt, recommend, explain the incomprehensible situation, answer all your questions.
What kind of team works on landscaping projects
To understand who creates the landscape in Ontario for the territory, let’s talk about our team of specialists. Captain Handy values its employees, who are professionals. Each employee has graduated from the higher education institution of the country, received a special profile education in the field of landscaping and landscape. They already have work experience confirmed by hundreds of successfully implemented projects.
All designers and masters are aware of the latest fashion trends in the landscape, can also offer their developments, ideas. Always be able to explain why a particular site does not need the same design as in a resort or on the image from a magazine. They will offer a compromise, an alternative suitable for the customer.
Specialist who is competent in the design of plots of land, before proposing a plan for future design, will take into account the location of the area, dendrology, climate features, customer wishes and will gather in a single project to look organic, stylish, original. It is more difficult if the customer does not know exactly what he wants, the task of the designer to collect scattered images, pick up under the area, to create an original landscape design on the site.
The company never give up the obligations, we perform works without attraction of external contractors. You can check a course of work at any stage, thus in detail we will tell about results. We can also provide photo reports upon request.
Captain Handy saves your time, money, and most importantly your nerves. Our specialists are happy for their work, we pay attention to any little thing – a stone, a twig or stump. In our capable hands, any little thing becomes a component of the future landscape of your dreams. For us, there are no long distances – we work not only in Toronto and the region, but all over Canada.
The times of similar manor territories with faceless gardens and beds are long gone. Today, thanks to the landscape design in Toronto can create an individual style of farmland, to emphasize the status of owners of the site and their preferences.
Landscaping in Ontario
Landscaping a garden in Toronto, country house or yard in Ontario from Captain Handy is a unique opportunity to refine the area, fill it with exquisite plants, correctly and harmoniously combine them and create the necessary stylistic concept.
It is important to understand that landscape design is a creative and creative process. At the same time, with the wrong approach to such work can harm the appearance of the territory and break the idyll.
That is why it is recommended to use the services of professional designers who have sufficient knowledge and practical experience in organizing and improving the garden area to create a landscaping of the cottage plot or yard (or any other).
The company “Captain Handy” offers you its professional services of landscape design and landscaping garden in Ontario, homestead or any other area.
In the process of creating a project, we clearly take into account the peculiarities of the area, its shape and a number of other factors, as well as listen to your recommendations and wishes. All in order to create an elite landscape design, which will qualitatively allocate your site among hundreds of others.
On our resource you can view photos and examples of design projects, as well as read reviews. Traditionally, for illustrative purposes, we place a photo before and after the embodiment of our creative and creative plan.
To use our services or to call in a specialist to carry out area measurements, we recommend using the order form or contact us in any other way convenient for you. If this is the case, you can also get specific advice and recommendations from our professional staff.
To order a project in the company “Captain Handy” is the first step to creating a beautiful country house design. To find out the prices for a particular project, you need to use the “Contacts” section and contact us or visit our cozy office for a personal conversation.
We work with a variety of different types of territory: ready to implement the landscape design of a small plot or implement a turnkey large and responsible project. The cost of landscaping in Ontario is discussed individually in each case.
To live in harmony with nature, to provide comfort and coziness is one of the tasks that we set ourselves. Our experience allows us to create any landscape, changing the landscape of the surrounding area and making your wishes come true.
You have an area that you have long dreamed of, but you are not satisfied with its terrain. Our highly qualified designers will develop a quality landscape design project for your site, so that you would like to work and enjoy the fruits of their work or relax with the whole family and enjoy life.
Landscape design is the art of combining the life-giving power of plants and man, an artificially created place that pleases everyone with beauty and wellbeing. Choose landscape design, and we can meet all your needs for the implementation of bold ideas.
If you order from us the landscape design of the dacha area, then free yourself from many problems with improvement, and we will create the perfect conditions for a perfect rest after a day of work and the city bustle. You can enjoy the silence and extraordinary beauty of your garden, walk comfortable winding paths to the recreation area, listening to the whispers of trees and admiring the picturesque artificial pond or sit on a bench with a volume of poems by your favorite poet, hiding from the hot summer in the shadow of exotic trees growing on the ledges of the terrace.
The landscape design of the Toronto site, made in collaboration with you creative project, will bring you a special, extraordinary unique feeling of fusion with nature.
Careful and practical paths covered with paving tiles will decorate any garden and garden. Paving elements are made of heavy concrete by vibrating or vibrating pressing. Vibropressed products are durable, resistant to moisture, frost and non-slip surface.
Paving tiles in Toronto of the cottage plot or territory near the private house is carried out by different schemes. But for beginners who have decided to do without the help of professionals, it is better to use simple laying options. Visual effect can be obtained without complicating the composition of work, a combination of tiles of the same shape and different colors.
Choosing a Tile Paving in Toronto. Scheme
Before you paving the paths in Toronto at a cottage or in the yard of a private home, the following points are determined:
The number of paths and their location. It is generally accepted that a central paved path leading from the gate to the house is mandatory. Its width should be such that it can be easily parted by 2 people. This is 1.0-1.5 m. If there is a car, there is a convenient passage to the canopy or garage.
Its width depends on the width of the car. There is another option – to make two parallel tracks for wheels. It is desirable to pave paths to all places frequented by residents and guests – a gazebo, an artificial reservoir, barbecue area, flower beds and beds.
The width of such trails usually does not exceed 80 cm. In any case, the width of the trail must be adjusted to the size of the tiles so that it does not need to be cut.
Paving material. The thickness of the tiles or paving stones in Toronto is selected depending on the functional purpose of the track. A paving stone is usually called a small pavement tile, the thickness of which is commensurate with its width and length.
Paving elements with a thickness of 60-80 mm are chosen for the lanes on which cars drive and people often walk, and up to 60 mm for decorative garden paths. Strong and non-slip tiles and paving stones of the required thickness can be purchased from the company producing concrete products “Lentehstrom”.
The scheme of laying – “column”, “herringbone”, “bandage”, “fan”, “roundabout”. Any ornaments are laid out from colored elements. It is better to entrust the implementation of complex schemes to professionals.
Before the start of work on the ground make a drawing on millimeter paper, on which sketches of paths in a certain scale are put. When using tiles of the same colour, the total area of the tracks is divided by the area of one tile. The number of elements shall be rounded up to the whole number.
The result obtained is multiplied by an increase coefficient of 1.1-1.15. Stock is needed in case of damage to concrete products during paving or because of the need to trim them. The more complex the contour of the path, the larger the stockpile must be.
Preparation works on the territory before stone paving
Work on the area begins with the contouring of future paths with pegs, between which the twine is stretched. The rope serves not only as a border, but also as a level. For tile laying you will need – shovels (bayonet and scoop), a long level, a rubber hammer, a tool for ramming (vibratory plate), a container for kneading cement and sand mortar, a brush, angle grinder. Further work on the arrangement of flat tracks is carried out in the following order.
A trench is made along the marked contours, the depth of which depends on the thickness of the preparatory layers and the tile itself. Geotextiles are laid on the compacted bottom of the trench to prevent weeds from germinating through the joints between the coating elements.
The thickness of the bearing gravel layer is 5-15 cm, sand layer – 5-10 cm, cement-sand (if it is provided) – 3-5 cm. Tile height for light loaded tracks is up to 6 cm, for loaded tracks – 6-8 cm. For this purpose crushed stone (gravel) with fraction of 5-20 mm and coarse fraction sand are used.
On hard dense soils, no gravel layer is required. For clayey or marshy soils, a crushed stone bearing layer of at least 10 cm thick will be required. Each layer should be embossed after backfilling. It is recommended to use an electric or gasoline compaction machine.
In the preparatory phase, sanding can be finished. But more often, the last layer is the cement-sand mixture. Components are mixed in dry form in the ratio of 1: (6-10). First, sand is poured into the container, cement is added to it and mixed.
In the manufacture of trenches provide a slope for water flow – 5 mm per 1 meter. This slope can be transverse, longitudinal, longitudinal-transverse. Water should flow on the lawn or into the drainage system, but not towards buildings. A cement binder prevents the sand from gradually leaching out. Cement binders are mainly used when constructing heavy traffic lanes.
Framing installation
To prevent the tiles from spraying, a fence is arranged for a pathway made of special curbstone or paving stone placed on a rib. The kerb is made hidden or visible, depending on the wish. Framing is mounted until the path is paved. For this purpose:
- Next to the path, trenches are made to the required depth.
- Tramble the ground.
- They make crushed stone falling off.
- Place the curb on a layer of cement-sand mortar or fine concrete.
Tile laying
How do you properly conduct the paving process?
- Start from visually and functionally important places (porch, house entrance).
- Lead the paving process in the direction “from yourself”.
- Check the straightness of the seams at every th ree rows.
- Place the paving elements with a rubber kiyan (light strokes).
After installing 3-5 m2 of tiles (before compacting them), use a long construction level to control the surface of the coating.
Read our blog!
Paving tiles in Toronto are durable and reliable coating, resistant to temperature fluctuations, humidity and other external factors. It is used at arrangement of pedestrian zones, parking places, platforms, stops. In order to extend the service life of a paving tile and preserve its decorative qualities, it is necessary to avoid factors that prematurely destroy it, to observe the conditions of operation and maintenance.
Basic rules for installation and maintenance of paving tiles in Toronto
The strength and durability of a tile coating can only be guaranteed if a set of conditions are met:
- tiles are selected according to the planned loads and climatic conditions;
- all technological rules have been observed during installation;
- the gutter is properly arranged;
- the operating conditions recommended for this material are complied with.
When laying paving tiles in Toronto, care must be taken to ensure that the joints do not get weedy. For this purpose, before installing the tile material on the prepared base put a geotextile, thick polyethylene film, roofing felt. Regular maintenance measures, to which they relate, significantly extend the service life of the tile coating:
- Regular preventive cleaning using special products. Able not only to extend the life of the coating, but also to maintain the brightness of the color. Such cleaning is recommended in spring after snow melting and in autumn. Preventive cleaning consists in washing the tiles and cleaning the seams.
- Reducing water absorption with water-repellent treatment. Such compositions do not let water inside the products. This is very important, especially for winter time. At negative temperatures, the water that has entered the capillaries of concrete tiles freezes, expands, creates internal pressure and gradually destroys the product from the inside. Water-repellent impregnation, which not only protects the material from moisture, but also makes its color more saturated, retains its characteristics for 10 years. At the end of this period, the treatment should be repeated. Another way to renew the surface of paving tiles is to apply special water-based, alkyd or polyurethane rubber paints. Alkyd dyes harden the surface, while polyurethane paints do not peel off the concrete surface even at -30 °C.
- Load control. Significant exceeding of the load levels, e.g. a heavy truck driving over a tile on a pedestrian walkway, leads to material breakage. Small but constant exceeding of the planned loads deforms the paving elements, increases their mobility and impairs the correct water flow.
- Control over the use of cleaning agents and tools. Experienced specialists recommend to use for regular maintenance and cleaning of heavy soiling only those chemical agents that are permitted by the regulations on material maintenance. Heavy and sharp tools are not permitted to be used in winter to fight ice and dense snow.
Ways to Care for Paving Tiles
All methods can be divided into three main categories:
- Mechanical. It is carried out by means of various tools – shovels, scrapers, spatulas. This method is usually used in winter to clean the surface from ice and snow.
- Chemical. All chemical agents are applied only to wet coating. Concentrated chlorine formulations can irreversibly change the colour of products. Therefore it is recommended to try them on a small, unobtrusive area before using the chemical agents.
- Wet or dry cleaning. This consists of cleaning the surface from dust, dirt, debris with plastic lint brushes and a pressure jet of water. This is the main method used for regular maintenance. Specialists do not recommend washing the tiles with water supplied at too high a pressure, as a high-pressure jet can destroy the material.
How to properly clear paving tiles in winter from ice and snow.
It is strictly forbidden to use metal-tipped shovels and other similar tools for cleaning tiles in winter. They can destroy the material surface, which is particularly sensitive to mechanical influences at negative temperatures. For cleaning it is recommended to use shovels with wooden and plastic working parts. Paving tiles touch the roadway from ice and snow are cleaned with a brush or a sidewalk sweeper.
To prevent the formation of ice and snow it is recommended to use anti-freeze reagents approved for coloured pavement tiles. Cheap, low-quality anti-freeze reagents change the original color of products for the worse. It will no longer be possible to restore the original decorative appearance of the coating. It is prohibited to sprinkle paths and platforms with salt. It has a destructive effect on the surface and inner structure of the tile, in which salt penetrates with water.
From time to time it is necessary to sprinkle the joints between the tiles with sand and replace damaged elements.
Paving tile care in the summertime
In summer, pavement tiles are cleaned of dust, dirt with brushes and water supplied under pressure. The following methods are used to remove complex dirt:
- Chewing gum. It can be removed with a special detergent or simply removed with a scraper and the rest can be cleaned with a brush.
- Gasoline and oil stains. To remove them, special decomposition agents are used. If gasoline and oil stains are sealed between the joints, the dirty sand is removed and filled with clean sand. Machine oil must be washed immediately as it affects the structure of the pavement tiles. Sand or sawdust should be poured onto the fresh spot and then gently removed.
- Tire tracks. They are removed with household detergents dissolved in hot water.
- Rust stains. In this case, the surface is cleaned with a concrete surface cleaner containing hydrochloric acid.
- Soot. Removed with a mixture of detergent and bleach dissolved in water or soapy water.
- Blood, wine. Special bleaching agents are used to combat these hard-to-remove stains, which can have a negative impact on health. Therefore, they are used with latex gloves and protective goggles. After cleaning, the surface is treated with water supplied under heavy pressure.
Make sure that no mortar or concrete mixes get on the tiles. It is practically impossible to clean the coating without damaging the surface. A mechanical method is used to remove such stains. When carrying out construction work after tile laying, it is necessary to protect the tiles with a dense polyethylene film. Tip! Freshly spilled liquids should not be rubbed with a cloth immediately. It is better to use an adsorbent with the following functions: sand, sawdust and even cat filler. Once the adsorbent has absorbed the liquid, it should be gently swept off the surface.
How to remove the pickles from the pavement tiles
The salts are white salt deposits that can appear on the surface of paving elements for several reasons. It is:
- Presence of salts in building materials and water used in manufacture of products.
- Violation of production technology.
- Violation of the rules of storage of products for paving. High humidity in storage areas leads to saturation of products with water and salts dissolved in it.
If there are no white spots on the purchased tiles, they are treated with a weak solution (5%) of acetic, citric or orthophosphoric acids for preventive purposes. After acid treatment, the products are applied hydrophobisator.
Salt plaque not only spoils the appearance of paving elements, but also leads to the gradual destruction of the structure. Therefore, if there are any salts, they must be quickly removed.
How to get rid of the grass between the pavement tiles
If no measures have been taken against weed germination during the installation of the coating, we will have to fight against it every year in summer.
How to remove grass between paving tiles are the main ways:
- Pull out weeds with root, cut as low as possible with scissors or other special tools.
- Pour boiling water over the seams. Alternatively, burn out with a blowtorch. But in the latter case, the surface of coloured tiles that are not designed for high temperatures can suffer.
- Rinsing the seams with water supplied under pressure. Liquid rinses out seeds caught between tile elements.
- In case of strong spread of weeds, herbicides are used. When using them, observe the specified dosages, otherwise you can cause damage to useful plants planted nearby.
The surface of a tile coating may be negatively affected by biologically active factors, such as moss and fungus. They gradually destroy the artificial stone and reduce its service life.
How to remove moss and fungus from paving tiles:
- to mechanically remove moss, fungus and lichen;
- moisten the surface;
- wipe the surface witch chlorine-containing substances dissolved in water;
- rinse the surface with water.
Preventive maintenance measures for tile coating include treatment with lawn solutions containing iron sulphates and ammonium. They prevent the appearance of moss, lichen and fungus.
Regular tile maintenance does not require any special time and financial expenditures. However, with the help of simple measures it is possible to significantly extend the working period of a paving tile and preserve its original appearance as long as possible.
People who are not familiar with the rules of stonework in Toronto are faced with the fact that the finishing material, after holding on to the wall for some time, gradually begins to collapse. Usually the stone is applied on the glue of low quality, although often incorrectly prepared work surface leads to a collapse of the cladding.
Methods of installation of a Stonework in Toronto – 2 variants
The laying of decorative stone is performed with the use of auxiliary materials, which are selected taking into account the planned method of installation. The tiles can be fixed on the wall with the use of jointing technique or seamless method: If the material is mounted with an expansion, then simultaneously with the tile is purchased the intended for its execution solution and a special dye. The latter usually has a contrasting tone or color corresponding to the tile shade.
If the decision is made to lay the stone without using the technique of expansion, then in addition to finishing, in the shop, you need to buy only the manufacturer’s recommended adhesive and, if necessary, hydrophobic composition.
A decorative stone brick in a seamless way is easier and faster than with stitching. Finishing material should be laid tightly, which will allow you to get a virtually monolithic surface. The main thing in the process of installation – time to remove excess adhesive that protrude in the sealing of the finish, otherwise you will have to suffer later.
Dried tile glue with decorative finishing help to remove special acid-containing compositions. A greater effect can be achieved if the cleaner was released by the same manufacturer as the glue.
Despite the difficulty of laying a decorative stone with an embossing, this method is used quite often – it looks more spectacular.
They fix the decorative stone on the wall at a certain distance from each other. A perfect joint can be achieved by placing the same pieces of plasterboard or chipboard between the rows of stones. After the installation of the entire finishing material, we wait for the glue to dry and then perform the jointing.
Too wide a seam can spoil the overall impression of the decoration, which is especially noticeable if the tiles are used to create a composition with the same pattern in the apartment.
Stonework in Toronto is our company’s best offer!
Stonework in Toronto : types of decorative material – sandstone, marble, limestone
For interior decoration of residential walls, stones are used, made either on cement mortar or on plaster. The first ones are chosen for facing surfaces in rooms with a high level of humidity, for example, in the kitchen and in the bathroom. The second type of products is afraid of water, so they are used to decorate walls in the living room, bedrooms and other rooms of the house / apartment. Finished products most often imitate brick and slate.
And if the brick looks perfect in the interior of corridors, bedrooms and balconies, then due to the variety of textures of oil shale it is possible to create bright and original compositions on the walls of living rooms and hallways. As for natural materials, because of their high cost, finishing with their use is rare. Meanwhile, the following types of decorative stones have become widespread:
- sandstone – has three shades, has a granular structure;
- marble – has a wide color palette and different texture;
- limestone – differs in structure, size and color shades.
The laying of natural decorative stone on the walls has its own peculiarities, but does not differ much from the installation of artificial products. The main thing in both cases is to properly prepare the surface.
Installation of a stonework in Toronto on the walls has its own peculiarities, but does not differ much from the installation of artificial products. The main thing in both cases is to properly prepare the surface.
Installation of a stonework in Toronto
We recommend that you carefully process the stonework in Toronto before laying them on the walls. The surface to be trimmed may have different coatings, so it is prepared differently: If you want to put the tiles on the plastered walls, the places with obvious defects are plastered again. Having got rid of convexities and voids in this way, the wall is treated with a dry brush, wetted with water and dried.
We prepare very rough surfaces in a similar way. We finish the process with priming works. As a primer can be used liquid adhesive mixture. After that, after 2-3 hours, we begin to lay tiles. The wooden working surface is preinsulated using pergamine sheets, the laying of which begins from the bottom upwards (with horizontal overlap – 15 cm, vertical overlap – 5 cm). Over the vapour barrier we equip the wire mesh.
We apply a layer of cement mortar to the wire mesh, and before the surface dries out we use a dry hard brush to improve the adhesive properties of both materials. Preparation of the metal wall for decorative tiles follows the same principle as for wooden surfaces. The difference is that in the first case the mesh is fixed by nails with small flat bars or by stapler, while here the screws are more appropriate.
We remove defects on stone, concrete and brick walls with the help of puttying. If there are greasy spots on the surface, we remove them with special degreasers. For preventive purposes, we reinforce the wall, apply cement mortar over it.
If the stone surface has been painted, then before laying the tiles it is treated with a sandblasting machine. Afterwards, we install the plastering grid and apply a cement layer. If it is planned to lay the decorative stone on the gypsum plasterboard, we apply a waterproofing composition beforehand. Installation is carried out with the use of a special adhesive, as a finishing material we recommend to choose light and thin types of products (heavy stone should be laid on a double layer of gypsum plasterboard).
The best landscaping company in East York – aims to transform the surrounding area, the contemplatio are one of the main landscaping works in the area.
Important indicators that the best landscaping company in East York is taking into account
Before landscaping in North York, it is important to find out as much as possible about the area’s climate, soil conditions, existing plantings and the crops to be planted.
The main climatic factor that determines the choice of plants and the nature of landscaping in general is temperature, since each plant has its own optimal temperature limits for normal growth.
The best landscaping company in York will help you turn all your plans into reality!
Another important indicator when drawing up a green area plan is the degree of illumination of the area as a whole and its individual parts. For uniform landscaping, you need to select the right light-loving and shade loving plants.
It is necessary to find out the fertility of the soil, this is the indicator that determines the quality of supply of planted plant crops with nutrients, water and air. Saturation with mineral elements, acidity, mechanical composition and so on – these are the indicators that determine the quality of soil. The best soil for plants is considered to be loamy and sandy loam.
Ground humidity is a very important indicator. Water is a necessary material for plant growth and its main component. Moisture helps to dissolve the minerals needed to feed the plants and to protect them from overheating.
The main supplier of moisture is precipitation, the average rate of which is taken into account when planning a green area.
Best Landscaping company – your step to a successful project!
Several key milestones in the best landscaping company in York
1. Dendrological plan
Landscaping in York begins with the drawing of an arboretum – a drawing on which the boundaries of the site, the buildings located on it, lines of communication, are applied to existing trees and shrubs, and then planned plantings.
Before the beginning of landscaping must take into account the location of the site relative to the sides of the world, on an open or sheltered from the wind is an area. Landscaping is done taking into account the topography of the area, as it plays a decisive role in decorating the garden space.
All these factors influence the selection of plantings for subsequent plantings. Experienced landscaping specialists in North York know very well how to emphasize the uniqueness of the natural terrain.
2. Planting decorative plants
The next important stage will be the selection and further planting of plants. The whole variety of plant forms is divided into several groups: trees (plants with a single trunk), shrubs (plants with several tree trunks), herbaceous (perennial and annual plants), they can also be divided into deciduous and evergreen.
3. Greening with evergreen plants
Coniferous plants stand out for their special beauty at any time of year, due to their variety of shapes, coloration of needles and trunks, these plants are indispensable for the decoration of any garden.
4. Planting perennial plants
Those parts of the garden that are free from trees and shrubs are filled with herbaceous plants, they have a fairly large group. Grass plants are divided into perennials, two-year-old and annual plants. For the design of columns and arches, curly green areas are used.
5. Lawn building
The final final stage in the landscaping of the North York site is sowing or laying the lawn. It is very important in the design of the territory to maintain a uniform style, then the site will look harmonious, cozy, comfortable and delight its owners all year round.
Best Landscaping company – a great choice for the homeowner!
Landscape design in East York
Landscaping Company in East York “Captain Handy” provides a full range of landscape design services in York. Our team includes specialists such as: landscape architect, landscape designer, sculptors, engineering communications specialist, dendrologist, florist, stone specialists, three work teams for landscape and landscaping in North York.
The works we perform: design, landscaping and landscaping, creation of decorative water reservoirs, installation of engineering communications, paving, as well as further maintenance of the territory.
We are always glad to come to the aid and fulfill any task set by the most demanding client. We provide services throughout Ontario. We operate in North York, East York, York, Toronto, Bolton, Aurora, etc.
Works which we carry out: designing, an accomplishment and gardening, creation of decorative reservoirs, watering, installation of engineering communications, paving, and also the further maintenance of territory.
We love our work, and you will be sure of it! A best landscaping company is an excellent, well-thought-out choice.
Landscape work in York
One of the most interesting and important stages of landscaping is landscape work in York.
Preliminary on your site should be performed the necessary engineering and construction work in accordance with the developed project: the creation of drainage system of the site, vertical layout of the area, constructed water bodies, prepared the soil for the growth of plants in accordance with the requirements of plants, etc..
Landscape in North York – planting plantations on the site (trees, shrubs, lawns, perennials, annuals, etc.), which form and decorate your garden. When planting trees and shrubs, lawns, perennials, annuals, etc., which form and decorate your garden, it is very important to imagine the appearance of your garden after a few years.
Otherwise, the same little tree planted to admire her in front of the window, after 10-15 years will grow into a huge green (or blue) beauty, which completely block the view from the window and shade the room in the house.
Another situation is also common: a beautiful little juniper planted next to the track (20-30 cm in diameter) gradually grows to 3-5 meters and completely covers the surface of the track. An important aspect in the selection of planting material is knowledge of plant varieties and the country of origin of the planting material.
For example, if you want to see annual early spring flowering of the flower buds, plant the ovata flower buds; in other species of flower buds, the flower buds almost freeze above the snow cover level every year.
Many dendrologists are very skeptical about plants grown in the Benelux countries, because the acclimation of such plants is somewhat difficult. Do the right thing with Captain Handy, a best landscaping company.
However, it is possible to ask for help from an experienced landscape designer in East York with a good knowledge of dendrology, who will be able to make the selection of plant material for the creation of a garden with all its features. The design of three-dimensional compositions of plants should be based on the laws and stylistics of landscape design in North York, while taking into account the differences in environmental requirements of plants by soil, lighting, hydrological regime, etc. It is also necessary to take into account differences of plants in growth strength, seasonal ornamentally.
It is desirable to think over the winter appearance of the garden: at this time of year in the foreground are coniferous trees and shrubs, as well as the skeletons of trees and shrubs and their bark, fruits.
Almost every landscape designer in North York has his or her own techniques and secrets for creating a beautiful garden.
Someone prefers bouquet planting, someone does not think of a garden without lighting, someone planted hedges in all areas. It’s a matter of personal taste and preference. Our many years of experience have shown that the best results are obtained through close collaboration between the client and an experienced landscape designer in East York.
In conclusion, we would like to note that landscaping, despite some difficulties, is an extremely interesting and exciting process. The result is a beautiful and harmonious garden, to which you always want to return. Try it, plant it and you will succeed.
And if you are in any doubt, please contact us. We will certainly develop and implement a landscape design project for your garden in York!
Landscape design companies in North York
The best solution would be to come to us. We are a landscaping company, offering design in North York and the area partially or “turnkey”. Describe us a picture of an ideal garden or a whole plot, and we will make it a reality!
Landscape design in York consists of several stages:
- Conversation with the customer – what he wants to see on the site, which plants he prefers, whether there will be water bodies;
- A visit by our staff to the site to assess the soil condition, the need for drainage and more;
- Selection of all planting materials – bushes, trees, flowers;
- Works on creation of a given landscape;
- Delivery of work to the customer.
With us all quickly and simply. Each of our work is a separate story, which was written only for our customer. All our landscape projects in East York are different, we try to offer each time something new and original. We use in design, as typical garden plants, and more rare copies.
Our landscaping company in East York is your dream!
By contacting us, you will learn what high service and professionalism are. In our team there are real masters of their craft – designers and designers who strive to make not just a beautiful landscape project, but a real masterpiece, every time new and unique. Using different plants, we create uniquely beautiful landscape projects in York.
Properly designed and laid out irrigation of the soil is also not in last place. In a word, we offer a variety of landscape projects in different styles, approaching this issue thoroughly and from all sides. Therefore, with us quality, profitable and most importantly, beautiful!
Each owner of a summer house is trying to make it more beautiful and well-groomed, but many mistakenly believe that the landscape design in Brampton on the six weaving – is something of a fantasy.
For the design of landscape design will hire a professional, any very impressive amount of money ready to make from your dacha put on a garden masterpiece, decorating it with alpine slides, waterfalls, gazebos, exotic plants and other fruits of innovation design ideas. But the fact is that most people can not afford the services of such an expert.
Create landscaping in Brampton with your own hands, show your imagination by taking the best from unique author’s ideas, which are filled with many specialized sites. Embody in life your most daring and bright ideas, trust your taste and intuition, create a landscape that you like.
Landscaping near me – Captain Handy.
Landscaping contractors are companies that deal with all kinds of landscaping services related to landscape design and improvement of both the backyard and the front yard.
Creating a landscape design is not easy work. The main condition – the desire, patience and a little imagination, and then the territory of your country house will look like a paradise, beautiful, stylish and harmonious. And you will enjoy the fruits of your creativity, because the creation of beauty is a huge satisfaction.
Good Landscaping Contractors – the experts who will make you happy!
Yard design in Brampton
Begin the development of the design of the yard of a private house should c routine, at first glance, cases: land works and planning. First of all, it is necessary to think over the placement of all elements. Zoning under the 3D-project (at least under the sketch created taking into account the area of a site and quality of illumination) will be optimum.
A tight and cool corner is an ideal place for a pergola in Brampton or a barbecue. The summer heat will not prevent you from enjoying a family holiday outdoors. On the title side you can have parties, a swimming pool and light figures are appropriate.
As a result, Brampton yard design elements such as alpine slides and rosaries (analogues for the plains) should be placed on the sunny side. Take care of a drainage mixture of sand and gravel in advance, as normal soil is not suitable for mountain plants.
Modern Patio in Brampton
An irreplaceable element of modern landscaping in Brampton – a fenced area near a holiday home. For many it is a novelty, but the custom to equip the courtyard dates back to the ancient times. The yard design in Brampton with a patio is typical for Spanish-Moorish architecture. Usual for us flower beds are the analogue of the Moorish florist, which differs significantly from the “conservative” English lawn. What can be used to decorate a patio?
- The coffee table, often made of vine, is a central element that can be replaced with a wooden dining table.
- The design of the courtyard of the house in the Provence style is hard to imagine without arches decorated with miniature roses.
- Garden figures. Ceramic dwarfs, kittens and hedgehogs are already classics that fill the atmosphere with a special coziness.
- You can give originality to them by using topiaries with dried flowers, coffee beans, nuts and cinnamon – sticks.
Landscaping Brampton – a synthesis of tradition and European trends. Flowers, lighting fixtures, ponds and lanterns – surround yourself and your loved ones with what you love, and a great mood is ensured!
Are landscaping companies essential in Ontario
Speaking of a private house plot, many imagine a garden or garden. But it doesn’t have to be that way. Today, new momentum is gaining momentum in the arrangement of the exterior of a private home in Brampton under the recreation area. We are already tired at work, so when you return home, you should allow yourself to relax and not run to dig beds or clean weeds. In this article Captain Handy tells you how to choose the Landscaping contractors for your private home.
Be prepared for the fact that the result of the landscaping contractors will be different from what you imagined. This is a common problem for customers, but no one is immune to it, because what you imagined mentally can not always be correctly understood by the contractor and not always correctly conveyed to the workers.
That would not fall for the bad landscaping contractors, ask them for examples of work or a website where a list of services is presented. According to the list of services you can understand how qualified the specialists are. If they have a narrow list of services – this may indicate that the company has just created and professionals have little experience and provide a small number of services.
If you’ve been told that they can’t realize your backyard vision, it doesn’t mean that the landscaping contractors are bad, maybe your idea just isn’t possible or the landscaping contractors just don’t have enough of the right equipment or tools. You can always find a compromise, communicating with a contractor hasn’t hurt anyone yet.
Landscaping contractors – should be your friends – if they tell you little about the work ahead and do not offer what and how to better it should already alert you.
Landscaping contractors will not always agree with your vision of those or other planned works, because thanks to their experience they understand that your desire will not always look neat or be structurally unacceptable.
Landscaping near me – Captain Handy
Original yard design of a private house in Brampton: a recreation area or a garden.
Of course, vegetables from a bed it is delicious, useful and always fresh, and do not run to the store. But it’s not always worth planting all the free honeycombs with them. You can take a small area under a vegetable garden, and the rest of the space to use for a different purpose.
Why don’t you “wrap up” your yard? Make it so attractive and comfortable that those passing by also want to look at the light? We suggest that you take a look at some of the landscaping companies essential in Ontario
Also read: Landscaping Brampton
The beauty created by our company is admirable and makes us proud of the work we have done. So we suggest you take advantage of the following interesting ideas:
- Greening the yard in Brampton by making a lawn, planting bushes or making flowerbeds;
- Making landscaping in Brampton interesting decorative elements such as: garden statues, flowerpots, old furniture, handicrafts;
- Create an original recreation area for yourself and your kids.
Landscaping near me Brampton
Captain Handy is the best landscaping contractor in Brampton and throughout the GTA. Our company provides absolutely any kind of landscaping services. We do all kinds of work in such areas as:
- hire a landscaper;
- tree services;
- retaining walls;
- landscaping job;
- lawn maintenance;
- garden landscape;
- and others.
A small yard of a private house is not yet a sentence for creating functional and beautiful design. As the size of the plot does not always allow for a terrace for relaxation or a large gazebo, you can create a small secluded corner with a table and chairs under a tree or by tall bushes that give shade. Hang garlands on the branches, homemade bottle lamps and a cachepot with flowers that will bring even more comfort.
Landscaping near me Brampton is quite easy to do with your own hands, as old garden tools, wheelbarrows, flowerpots and almost any outdated items that can be turned into decor are ideal for creating a style.
The paths in the landscape design of the private home in the recommended finish with natural stone, tiles or pebbles. You can also decorate the country courtyard with flowering plants without fear of “overdoing it”.
The veranda in Bolton is a stylish and functional decoration of the country estate. But if the gazebo is a free-standing structure that can be used in the summer, the veranda in Markham is an attached room to the house, with a roof, walls and is designed for year-round use. Warm veranda in York can serve as a corridor, entrance hall or rest room, greenhouse, winter garden, it can even accommodate a swimming pool.
What’s the difference between a veranda in North York and a terrace? These concepts are often confused, although they have a constructive and visual difference. With a roof and walls, that’s the difference between a veranda and a terrace and a porch.
The veranda is envisaged at the stage of construction of the house, but more often it is completed already during the operation. That’s why many people are interested in how to build a veranda in Aurora with their own hands. Below is a step-by-step instruction on how to build a veranda to a private house.
Build a veranda in Bolton
Any construction in Scarborough starts with project development.
Summarizing the experience of building verandas in Toronto, we can note that they differ in the following parameters:
Location (adjoining the house):
- Corner veranda
- End veranda
- Facade veranda
Degree of closure:
- Open veranda
- Closed veranda
By installing the veranda sliding doors, you can transform a closed veranda into an open one.
It’s a design feature:
- Built-in veranda (built together with the house, has a common foundation).
- Adjoined (built as needed, has its own foundation).
The shape of the veranda:
- The popular form is a rectangle
- Round veranda
- Multiangle
The main purpose of the veranda in Richmond hill is to make the house or summer cottage more spacious and decorate the building. Addition of a veranda in GTA performs a purely utilitarian function – the insulation of the house. Therefore, it is logical to ask how to add a veranda to the house correctly.
Despite the fact that the veranda – a summer construction, its construction provides for a number of rules.
Which is part of the veranda construction project:
- location of the veranda. The main options are marked above. It is important that the annex is an extension of the house, representing a common architectural ensemble with it.
- entrance place to the veranda. The entrance can be arranged from the street, from one of the rooms or it can be through, through the street to the house;
- the place of installation of the door. Entrance doors to the veranda and the house is undesirable to place against each other, otherwise drafts cannot be avoided;
- the size of the veranda in the house. The length of the veranda is usually the length of the wall along which it is erected. The width is from 2.5 to 7 m. Here it is important that the size of the veranda proportionally corresponds to the size of the house.
How to add a veranda to a wooden house in Toronto
Any addition to the house made of wood is made after shrinking the structure. A house made of timber or log gives shrinkage for a certain period (the most active first 2-3 years). To avoid distortion of the walls, you need to wait for this period, or think about connecting to the house, allowing the framework to play.
Tools and materials for veranda construction in Vaughan
The tool depends on what material will be used to build the extension in Vaughan. For wood you need: a hacksaw, a screwdriver, a hammer and an axe, a sledgehammer, a tape measure, a plummet, a level (construction and water), a corner, a cord for marking, a shovel. For the metal frame you will need an additional grinder tool and a welding machine.
Material
The (budget) version of the veranda is a metal frame covered with plywood, OSB plates or plastic wagon.
A more presentable look is a veranda made of bricks, natural stone or wood. Here it is important that the material of the annex matches the material from which the house, summer cottage is built or harmonizes (blends) with them.
The construction of a wooden veranda in Bolton will require: lumber (log or beam, board, rail), fasteners (elements), protective mortars for wood, crushed stone, concrete, bitumen, olive or roofing material, window and door systems.
For verandas with metal frame: lumber will replace metal corners and steel profile, solutions for metal processing will be added, and otherwise the materials will be the same.
The polycarbonate veranda is well-proven to allow you to freely admire the surrounding landscape. In addition, polycarbonate retains heat well, lets in light, can be used for walls and roofing. Plus, the cost of the material is quite adequate.
Cellular polycarbonate with wall thickness of 14-18 mm is used.
Preparing to build in Aurora
Construction of the veranda in Aurora begins with the preparation of the site. The part of the plot allocated for the veranda becomes a construction site. Before the work begins it is necessary:
- remove the visor above the entrance;
- remove the porch;
- clear the area of greenery and debris;
- remove part of the turf;
- think over the place of laying of building materials and construction waste
Naturally, landscaping in Ontario of the territory is most correct to perform with the direct participation of a professional who has the necessary experience and knowledge base. His services include the necessary advice and assistance in the work itself.
But it’s not always possible to have a specialist and you have to try out the role of a landscape designer in Ontario yourself.
If there is a great desire to try something on their own, why not? In general, if the fantasy is all right, then an independent construction of the garden in Ontario will not be such a big problem.
First of all, it is necessary to go around the whole site, assessing it for yourself. Determine which places to emphasize and which to hide. Which part of the territory beckons to you, and how to the contrary – makes you leave faster.
It is also worth paying attention to where the sunnier zone is and where the shade is. This factor can play a decisive role in the arrangement of the recreation area.
While walking around the territory of the future garden, take a close look at all possible details, mentally lay out the tracks of the desired material, choose the most successful way. Take a walk through the paths to find the most comfortable areas on which a proposed bench can be placed.
Landscaping in Ontario – contact our team!
Necessary details for a landscaping in Ontario
In order to approximate the general view of the area, you need to at least schematically capture it on paper. This plan should contain all the desired buildings, decoration elements, paths in Ontario, sites and distribution to the desired areas.
If you plan directly on the site, ordinary sand will be your loyal assistant. Just emboss it on the proposed places of future paths, mark the boundaries between zones and the proposed channel of a dry stream.
If you already have your own special area in the garden where you are used to dinner, just give it some novelty. Refresh your trees, put in new exterior items, and make a cobblestone walkway in Ontario. This will not only breathe new life into the site, but also make it more cozy and, of course, beautiful.
If you want to grow on your lawn, you should carefully inspect the area for any excess moisture. After all, if it is present, you will have to install an additional drainage system so that the lawn simply does not rot.
If there is any doubt about the quality of the soil, it is better to replace it with a new, more fertilized.
And yet to start site development is only when there is at least a basic knowledge of landscape design. Otherwise, the money spent on the landscaping in Ontario will be wasted.
Custom types of sites – advice from a landscaping in Ontario
Unfortunately, it is not always the right shape and size for the site.
The most common problem for a designer planning a site in Ontario is the non-standard shape of the site: too narrow or long.
Often there are cases when the width of such an area reaches only a couple of meters, but the length of 10 times more.
Landscaping a plot of land in Ontario is difficult, but it is workable. And the result is entirely up to you.
An Ontario garden from a non-standard shape will look beautiful and harmonious only with certain tricks that will help smooth out most of the disadvantages of the area.
Landscape design in Ontario
Setting up a site in Ontario should start directly from the zoning. You should divide the entire garden area into different separate zones, some of which can be set aside for plants and others for sites.
It is good if the elements are not protected from each other by walls that prevent you from looking behind the garden. The open space visually extends the area.
It is also much more pleasant if the different areas are different from each other. For example coating, plants, colors or different levels of sites.
For example, you can place a decorative lawn in the rest area, but pour a small stone under the trees. You can also beautifully beat the reception of sites of different levels: Lift up the furthest corner of the site slightly, thus visually softening the length of the garden.
The uneven size of the areas also gives the area some dynamics. Expansion can be achieved by using different edges, plant hedges and cobbled paths in Ontario.
If we talk about the walkways, they should not be straight under any conditions. Winding multi-coloured paths will add a certain variety to the overall concept of the garden. Vegetation of different types at the edges of the section will only have a positive effect on it.
A very important element for this type of site is the emphasis on individual elements. There should be at least three main points of attraction for the eye. These can be shrubs of unusual color or shape, benches or even sculptures.
Planting trees of different sizes also has a good visual effect. Just do not plant them too long in rows.
Award-winning Landscaping Company
CONTACT US TODAY
for a Free Estimate!
Contact us and speak with one of our service professionals to schedule a visit today!
GET A FREE QUOTE